60/70 penetration grade bitumen drums loaded for export from Durban, South Africa

Road construction · Bulk supply · South Africa

Bitumen grades & ADR transport

60/70 and 70/100 paving bitumen, 65% anionic emulsion and MC-30 cutback for contractors, asphalt plants and road-project buyers. Compare packing and starting order quantities, then confirm the transport plan for your destination.

Grades, packing & minimum orders

Existing catalogue options are shown below; availability, final specification and order quantities require written confirmation.

60/70 penetration grade bitumen drums loaded for export from Durban, South Africa

BTM-6070

Penetration Grade Bitumen 60/70

Harder-grade 60/70 penetration bitumen for hot-climate pavements, heavy-duty asphalt and high axle-load road construction.

Grade / key specification
60/70 penetration grade, unmodified paving bitumen · Penetration at 25°C: 60–70 dmm
Packing options
  • New steel drums, 180 kg net
  • New steel drums, 200 kg net
  • Bulk bitutainer, 20–24 t
Starting minimum order
1 × 20ft container (approx. 20 t drummed)
Full specification & documentation
70/100 penetration grade bitumen in steel drums supplied in bulk from South Africa

BTM-70100

Penetration Grade Bitumen 70/100

Refinery-produced 70/100 penetration grade bitumen for hot-mix asphalt, surface dressing and chip seal work in temperate and moderate-climate road programmes.

Grade / key specification
70/100 penetration grade, unmodified paving bitumen · Penetration at 25°C: 70–100 dmm
Packing options
  • New steel drums, 180 kg net
  • New steel drums, 200 kg net
  • Bulk bitutainer, 20–24 t
  • Jumbo polyamide bags on request
Starting minimum order
1 × 20ft container (approx. 20 t drummed)
Full specification & documentation
Anionic bitumen emulsion drums prepared for bulk export from South Africa

BTM-EA65

Anionic Bitumen Emulsion 65%

Water-based anionic bitumen emulsion at 65% residual binder for tack coats, prime coats and cold surface treatments.

Grade / key specification
Anionic slow-setting emulsion, 65% residual binder · Residual binder content: 64–66 %
Packing options
  • 200 litre steel drums
  • 1,000 litre IBC totes
  • Bulk road tanker for regional delivery
Starting minimum order
1 × 20ft container (approx. 80 drums)
Full specification & documentation
MC-30 cutback bitumen drums staged for export shipment from South Africa

BTM-MC30

Cutback Bitumen MC-30

Medium-curing cutback bitumen MC-30 for priming granular bases ahead of asphalt surfacing.

Grade / key specification
MC-30 medium-curing cutback bitumen · Kinematic viscosity at 60°C: 30–60 cSt
Packing options
  • 200 litre steel drums
  • Bulk road tanker for regional delivery
Starting minimum order
1 × 20ft container (approx. 80 drums)
Full specification & documentation

For 180 kg drums, a planning load of 110 drums is 19.8 tonnes net. This is not a guaranteed container payload: packaging weight, carrier acceptance, axle limits and port restrictions must be checked. Do not assume a 40ft container permits a heavier legal load.

ADR depends on the cargo, not the grade name

ADR is a transport framework, not a product specification or a certification of this supplier.

Cooled penetration bitumen

60/70 and 70/100 carried as cooled solids may be outside dangerous-goods transport classification. Confirm the actual product SDS; a drum alone does not establish exemption.

Hot liquid bitumen

Liquid carried at 100°C or above and below its flash point may fall under UN 3257, ELEVATED TEMPERATURE LIQUID, N.O.S., Class 9, packing group III, when not otherwise classified. The carrier must confirm the correct entry and equipment.

Cutback & emulsion

MC-30 is listed as Class 3 flammable liquid in this catalogue. Confirm its UN number, packing group and carrier acceptance from the current SDS. Assess emulsion separately; do not transfer a cutback classification to it.

South African road legs follow applicable national requirements; ADR applies to road legs within its scope. Sea freight uses the IMDG Code. No ADR-certified fleet, automatic exemption or pre-approved route is promised here.

Transport references: UNECE ADR 2025 · IMO dangerous goods and IMDG. The supplier SDS and carrier assessment govern the actual shipment.

Plan the shipment before booking

Drummed or bulk

Drums need unloading equipment and a suitable melting system before use. Bulk bitutainers require compatible heating and pumping facilities. Agree equipment, discharge access and handling responsibilities before ordering.

Route & delivery terms

Request EXW, FOB, CFR or CIF where listed for your grade; MC-30 is listed with EXW, FOB and CFR. Provide the delivery town or port and any onward road leg. Freight, sailing dates and transit times are confirmed in the quotation, not guaranteed here.

Documents & carrier checks

Request the current SDS, technical data sheet and batch COA, plus invoice, packing list and origin documents. Where regulated, confirm DG transport documents, marks, labels, equipment approvals and driver requirements with the carrier before loading.

Bitumen buying & transport questions

Is ADR a bitumen grade?

No. ADR is the agreement governing international carriage of dangerous goods by road between its contracting parties. Specify the bitumen grade separately, then confirm transport classification from the supplier’s current Safety Data Sheet and the actual carriage temperature.

Is every bitumen shipment dangerous goods?

No blanket classification applies. Unmodified penetration bitumen carried as a cooled solid may fall outside dangerous-goods transport rules; hot liquid and solvent-containing cutbacks need a separate assessment. The actual formulation, temperature and SDS determine the classification.

What is the minimum order for 60/70 or 70/100?

The catalogue starting quantity is one 20ft container, approximately 20 tonnes drummed. Bulk bitutainer loads are listed at 20–24 tonnes. Confirm the net quantity, equipment and route-specific payload in the written quotation.

Does ADR automatically cover delivery within South Africa?

No. South African road carriage follows applicable national dangerous-goods requirements. ADR applies where the road leg falls within its scope; sea carriage is assessed under the IMDG Code. Ask the carrier to confirm the rules for every leg.

Request your bitumen supply plan

Send your grade and governing standard, tonnes required, packing preference, destination, required delivery date and Incoterm. For bulk delivery, include receiving-tank capacity, heating and pump compatibility. Attach any tender specification or transport restrictions.